歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

超聲波清洗設備的正確操作程序

作者：admin來源：http://m.zhuohengsh.com/時間：2022-05-30

當你購買超聲波清洗機時，你應該仔細學習超聲波清洗機的說明書，請妥善保管，以備將來使用。現在我們來談談超聲波清洗機的操作程序。

When you buy an ultrasonic cleaner, you should carefully study the manual of the ultrasonic cleaner. Please keep it properly for future use. Now let's talk about the operation procedure of the ultrasonic cleaning machine.

超聲波清洗機的電源線一般與清洗槽分開。，將超聲波電源與清洗槽連接。帶排水管的超聲波清洗機可以連接排水管并使排水管朝向排水處。

The power line of the ultrasonic cleaning machine is generally separated from the cleaning tank., Connect the ultrasonic power supply to the cleaning tank. The ultrasonic cleaning machine with drainage pipe can connect the drainage pipe and make the drainage pipe face the drainage place.

向清洗槽中加入適量的清水。液位應能淹沒清洗后的零件，并低于高水位。有些型號有溢流管，因此應提前連接溢流管。

Add an appropriate amount of clean water to the cleaning tank. The liquid level shall be able to submerge the cleaned parts and be lower than the high water level. Some models have overflow pipe, so the overflow pipe should be connected in advance.

啟動電加熱開關，將水溫調節到合適的溫度（一般在50℃-60℃之間）。清洗機里有一個溫度檢測器。加熱裝置將繼續加熱至規定溫度，然后進入保溫模式。當溫度低于一定值時，加熱裝置將自動啟動并加熱至設定溫度。

Start the electric heating switch and adjust the water temperature to the appropriate temperature (generally between 50 ℃ -60 ℃). There is a temperature detector in the washing machine. The heating device will continue to heat to the specified temperature, and then enter the insulation mode. When the temperature is lower than a certain value, the heating device will automatically start and heat to the set temperature.

當水溫升至30℃左右時，可根據產品工藝向清洗槽中加入零件清洗劑，比例為1:20或1:30。攪拌干凈的水，使清洗劑完全溶解在水中。

When the water temperature rises to about 30 ℃, the part cleaning agent can be added to the cleaning tank according to the product process, and the proportion is 1:20 or 1:30. Stir the clean water to completely dissolve the detergent in the water.

使用超聲波清洗機清洗某些油漬較重的零件時，可在清洗前提前刮去較厚的油泥或較厚的粉塵。簡單的超聲波清洗預處理將大大提高超聲波清洗效率，縮短超聲波清洗時間，延長超聲波清洗機的使用壽命。

When using ultrasonic cleaning machine to clean some parts with heavy oil stains, the thicker sludge or dust can be scraped off in advance before cleaning. Simple ultrasonic cleaning pretreatment will greatly improve the efficiency of ultrasonic cleaning, shorten the ultrasonic cleaning time and prolong the service life of the ultrasonic cleaning machine.
超聲波清洗設備

將零件放入不銹鋼清洗籃中，輕輕放入清洗槽中。建議不要一次放置太多零件。盡可能均勻地攤鋪，不要放得太緊。

Put the parts into the stainless steel cleaning basket and gently into the cleaning tank. It is recommended not to place too many parts at once. Pave as evenly as possible without placing too tightly.

打開超聲波發生器電源，開始正常清潔工作。如有必要，順時針轉動功率調節旋鈕以調節適當的功率。電流表顯示正常電流為4-5安培。

Turn on the power supply of the ultrasonic generator and start the normal cleaning work. If necessary, turn the power adjustment knob clockwise to adjust the appropriate power. The ammeter shows a normal current of 4-5 amps.

超聲波清洗的工作時間可根據零件狀況確定。如果您在超聲波清洗過程中感覺清洗幾乎完成，可以先將電源旋鈕調整到小，然后按下超聲波工作按鈕。通常，您可以直接關閉超聲波電源。

The working time of ultrasonic cleaning can be determined according to the condition of parts. If you feel that the cleaning is almost completed during the ultrasonic cleaning process, you can first adjust the power knob to small, and then press the ultrasonic work button. Usually, you can turn off the ultrasonic power directly.

直接取出清洗籃，用清水沖洗干凈的零件。之后，將零部件放入風扇或空氣干燥器中進行空氣干燥，直到它們在間隙通道中完全干燥。一些用戶直接使用雙槽或三槽清洗機，一槽用于超聲波清洗，二槽用于水漂洗，三槽用于熱風烘干，這樣就省去了到處移動工件的麻煩。

Take out the cleaning basket directly and wash the cleaned parts with clean water. After that, put the parts into a fan or air dryer for air drying until they are completely dried in the clearance channel. Some users directly use double or three tank cleaning machines. One tank is used for ultrasonic cleaning, two tanks are used for water rinsing, and three tanks are used for hot air drying, which saves the trouble of moving workpieces everywhere.

當超聲波清洗設備用于清洗許多零件時，清洗液中的油泥含量非常高。再加上超聲波的乳化作用，清洗液會變得渾濁。這樣不僅使二次污染零件，而且可以削弱超聲波的空化作用。此時，不應再使用含有清洗劑的液體。

When the ultrasonic cleaning machine is used to clean many parts, the oil sludge content in the cleaning solution is very high. Coupled with the emulsification of ultrasonic, the cleaning fluid will become turbid. In this way, not only the parts are polluted twice, but also the cavitation effect of ultrasonic wave can be weakened. At this time, the liquid containing cleaning agent should not be used.

超聲波清洗設備的正確操作程序價相關內容具打這里了，您如果有什么想法的話歡迎關注我們m.zhuohengsh.com！

The correct operation procedures of ultrasonic cleaning equipment are listed here. If you have any ideas, please follow us at www.jnthcsb Com!

上一篇：各類清洗機清洗的共同重要常識
下一篇：一種通過式噴淋清洗機及其清洗方法