多槽手動超聲波清洗機的使用方法相對簡單，但為了確保最佳的清洗效果和安全性，需要遵循一定的操作步驟。以下是詳細的使用方法：

The usage method of the multi slot manual ultrasonic cleaning machine is relatively simple, but in order to ensure the best cleaning effect and safety, certain operating steps need to be followed. The following is a detailed usage method:

一、準備工作

1、 Preparation work

環境準備：確保清洗環境通風良好，干燥無塵，以避免灰塵和濕氣對清洗效果和機器造成不良影響。

Environmental preparation: Ensure that the cleaning environment is well ventilated, dry and dust-free to avoid adverse effects of dust and moisture on the cleaning effect and machine.

檢查設備：輕微搖晃機器，聽機箱內有無響聲，確認零件有否松脫。確認清洗機的各個部件完好無損，特別是超聲波發射棒和清洗槽。

Check equipment: Gently shake the machine, listen for any noise inside the chassis, and confirm if any parts are loose. Confirm that all components of the cleaning machine are intact and undamaged, especially the ultrasonic emitter and cleaning tank.

放置設備：將清洗機放置在平穩、水平的地面上，確保其在工作過程中不會晃動或傾倒。

Placement of equipment: Place the cleaning machine on a stable and level surface, ensuring that it does not shake or tilt during operation.

二、填充清洗液

2、 Fill with cleaning solution

選擇合適的清洗槽：根據清洗物品的大小和數量，選擇合適的清洗槽位。

Choose the appropriate cleaning tank: Select the appropriate cleaning tank position based on the size and quantity of the cleaning items.

添加清洗液：向清洗槽中加入適量的清洗液。一般來說，可以使用清水或中性清潔劑作為清洗液。如果需要加熱清洗液，應確保液位不低于槽深的2/3，以避免加熱過程中液位下降過多。

Add cleaning solution: Add an appropriate amount of cleaning solution to the cleaning tank. Generally speaking, water or neutral cleaning agents can be used as cleaning solutions. If it is necessary to heat the cleaning solution, it should be ensured that the liquid level is not lower than 2/3 of the tank depth to avoid excessive liquid level drop during the heating process.

調整液位：確保清洗液的液位高出發射棒約10cm，以保證超聲波能夠充分作用于清洗液中的物品。

Adjust the liquid level: Ensure that the liquid level of the cleaning solution is about 10cm higher than the emitting rod to ensure that the ultrasonic waves can fully act on the items in the cleaning solution.

三、啟動清洗機

3、 Start the cleaning machine

啟動發射棒：在加入清洗液后，先啟動發射棒，并調節到適當位置。待槽位內液位上升至發射棒一半高度時，方可啟動清洗程序。

Start the firing rod: After adding the cleaning solution, start the firing rod first and adjust it to the appropriate position. The cleaning program can only be started when the liquid level in the slot rises to half the height of the launch rod.

設置清洗時間和溫度：根據清洗物品的需求和清洗液的特性，設置合適的清洗時間和溫度。一般來說，清洗時間在5~15分鐘內可達到理想的清洗效果。如果需要加熱清洗液，應調節至適當?shù)臏囟龋ㄈ?0-60度），以提高清洗效果。

Set cleaning time and temperature: Based on the needs of the cleaning items and the characteristics of the cleaning solution, set the appropriate cleaning time and temperature. Generally speaking, the ideal cleaning effect can be achieved within 5-15 minutes of cleaning. If it is necessary to heat the cleaning solution, it should be adjusted to an appropriate temperature (such as 40-60 degrees) to improve the cleaning effect.

啟動清洗程序：按下清洗機上的啟動按鈕，開始清洗程序。此時，超聲波波能會產生并作用于清洗液中的物品。

Start cleaning program: Press the start button on the cleaning machine to start the cleaning program. At this point, ultrasonic waves can generate and act on the items in the cleaning solution.

四、清洗過程與監控

4、 Cleaning process and monitoring

監控清洗過程：在清洗過程中，應密切關注清洗機的運行狀態和清洗效果。如果發現異常情況（如聲音異常、清洗液濺出等），應立即停機檢查并排除故障。

Monitoring the cleaning process: During the cleaning process, close attention should be paid to the operating status and cleaning effect of the cleaning machine. If any abnormal situation is found (such as abnormal sound, splashing of cleaning solution, etc.), the machine should be stopped immediately for inspection and troubleshooting.

避免離開：在清洗過程中，不要離開清洗機太遠或長時間無人看管，以防止發生意外情況。

Avoid leaving: During the cleaning process, do not leave the cleaning machine too far away or unattended for a long time to prevent unexpected situations.

五、清洗后處理

5、 Post cleaning treatment

取出清洗物品：待清洗完成后，及時將清洗物品從清洗槽中取出。注意避免燙傷或劃傷手部。

Remove cleaning items: After cleaning is completed, promptly remove the cleaning items from the cleaning tank. Be careful not to burn or scratch your hands.

清洗槽清洗：用清水將清洗槽中的清洗劑沖掉，并用干凈的布擦拭干凈。確保清洗槽內無殘留物或清洗劑。

Cleaning tank cleaning: Rinse off the cleaning agent in the cleaning tank with clean water and wipe it clean with a clean cloth. Ensure that there are no residues or cleaning agents in the cleaning tank.

機器維護：清洗完成后，將清洗機放在干燥通風的地方，以便其自然晾干。定期檢查清洗機的各個部件是否完好無損，如有損壞應及時更換或維修。

Machine maintenance: After cleaning, place the cleaning machine in a dry and ventilated place for it to air dry naturally. Regularly check whether the various components of the cleaning machine are intact and undamaged. If there is any damage, they should be replaced or repaired in a timely manner.

六、注意事項

6、 Precautions

閱讀說明書：在使用前請仔細閱讀清洗機的說明書，了解其基本結構、操作方法和安全注意事項。

Read the instruction manual: Before use, please carefully read the manual of the cleaning machine to understand its basic structure, operating methods, and safety precautions.

正確連接電源：請確保所供電源有可靠接地線，以避免觸電危險。

Correctly connect the power supply: Please ensure that the supplied power supply has a reliable grounding wire to avoid the risk of electric shock.

避免不當使用：請勿將清洗機用于不適當?shù)奈锲坊颦h(huán)境中，以免造成人身傷害或財產損失。

Avoid improper use: Do not use the cleaning machine in inappropriate items or environments to avoid personal injury or property damage.

注意安全：在操作過程中應注意安全，避免手部或其他身體部位接觸到高速旋轉的部件或高溫的清洗液。

Attention to safety: During operation, attention should be paid to safety and avoid contact between hands or other body parts and high-speed rotating components or high-temperature cleaning solutions.

通過遵循以上步驟和注意事項，您可以有效地使用多槽手動超聲波清洗機進行清洗工作，并確保其長期穩定運行。

By following the above steps and precautions, you can effectively use a multi slot manual ultrasonic cleaning machine for cleaning work and ensure its long-term stable operation.

本文由多槽手動超聲波清洗機友情奉獻.更多有關的知識請點擊:http://m.zhuohengsh.com 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from a multi slot manual ultrasonic cleaning machine. For more related knowledge, please click: http://m.zhuohengsh.com Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned