歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

超聲波清洗機：超聲波清洗閥體的原理

作者：創始人來源：http://m.zhuohengsh.com/時間：2025-08-30

　　超聲波清洗閥體的原理主要基于超聲波在液體介質中產生的空化作用。當超聲波在液體中傳播時，會產生數以萬計的微小氣泡，這些氣泡在聲壓作用下迅速膨脹和破裂，形成強烈的沖擊力。這種沖擊力能夠剝離附著在閥體表面的污垢，包括油脂、鐵銹、焊渣、塵埃等，即使是閥體內部的微小通道和縫隙也能得到徹底清洗。

　　The principle of ultrasonic cleaning of valve bodies is mainly based on the cavitation effect generated by ultrasonic waves in liquid media. When ultrasound propagates in liquid, tens of thousands of tiny bubbles are generated, which rapidly expand and rupture under the action of sound pressure, forming a strong impact force. This impact force can peel off dirt attached to the surface of the valve body, including grease, rust, welding slag, dust, etc. Even small channels and gaps inside the valve body can be thoroughly cleaned.

　　清洗工藝流程：上料→超聲粗洗→超聲精洗→熱水漂洗→熱燙漂洗→吹水→下料

　　Cleaning process: Loading → Ultrasonic rough cleaning → Ultrasonic fine cleaning → Hot water rinsing → Hot scalding rinsing → Blowing water → Unloading

　　1. 清潔各水槽，關閉各水槽排水閥門。開啟各水槽的進水閥門，待水位高于液位浮球關閉進水閥門。

　　1. Clean each sink and close the drain valves of each sink. Open the inlet valves of each water tank and close the inlet valves when the water level is above the liquid level.

　　2.開啟總電源進入人機面板按開始進入工作畫面。

　　2. Turn on the main power and enter the human-machine panel. Press the start button to enter the work screen.

　　3.按ON開啟照明，按ON開啟吸霧風機。

　　3. Press ON to turn on the lighting, and press ON to turn on the mist suction fan.

　　4.旋轉按鈕開關開啟一號槽二號槽三號槽四號槽加熱開關。

　　4. Rotate the button switch to turn on the heating switch for slots 1, 2, 3, and 4.

　　5.設置好各槽所需溫度（一號槽50~65度，二號槽50~65度，三號槽50~65 度，四號槽50~65度）。具體按工藝要求設置。

　　5. Set the required temperature for each slot (50-65 degrees for slot 1, 50-65 degrees for slot 2, 50-65 degrees for slot 3, and 50-65 degrees for slot 4). Set according to the specific process requirements.

　　6.待各區域溫度升到所需溫度各水槽加入所需清洗劑，進入人機畫面，在進入參數設置：滴水時間（1000~2000）毫秒，清洗時間（100000~300000）秒，（注：其余參數不能隨意設定）。

　　6. When the temperature in each area reaches the required level, add the required cleaning agent to each water tank, enter the human-machine interface, and then enter the parameter settings: drip time (1000-2000) milliseconds, cleaning time (100000-30000) seconds, (note: other parameters cannot be set arbitrarily).

　　7.進入人機畫面，再進入自動頁面按自動，紅色不在原位，藍色即在原位，顯示原位，若不在原位按機器復位后開啟復位，到達原位后按按鈕開關啟動。

　　7. Enter the human-machine interface, then enter the automatic page and press' Auto '. The red color is not in its original position, and the blue color is in its original position, displaying the original position. If it is not in its original position, press the machine reset button to turn on the reset. After reaching the original position, press the button switch to start.

　　8.放入裝有產品的清洗筐推車（注：清洗筐必須到位）。

　　8. Place the cleaning basket cart containing the product (note: the cleaning basket must be in place).

　　9.待清洗產品到達出料口，氣槍吹干剩余水分。籃筐拉入推車。

　　9. When the product to be cleaned reaches the discharge port, dry the remaining moisture with an air gun. Pull the basket into the cart.

　　10.如中途有上下前后越位以及其他緊急狀況，按下急停按鈕，進入人機頁面，按自動切換手動，再按上下左右前后調到原位。到達原位后手動切換成自動。在按啟動按鈕。

　　10. In case of up, down, front, back offside and other emergencies in the middle, press the emergency stop button to enter the human-machine page, press the automatic switch manual, and then press up, down, left, right, front and back to the original position. After reaching the original position, manually switch to automatic mode. Press the start button.

　　利用高頻聲波，在液體中產生的震動，形成強大的清洗力。每一個閥門出廠前都嚴格按流程清洗，確保全程無憂 “凈” 界；清洗槽溫度鎖定 50 - 65 度，在此溫度區間，清洗液活性被充分激發，油污、雜質紛紛從閥門表面松動瓦解，滴水時間精細調控在 1000 - 2000 毫秒，超長清洗時間達 100000 - 300000 秒，有效去除油脂銹跡炭渣等頑固污垢。

　　Utilizing high-frequency sound waves to generate vibrations in liquid, creating a powerful cleaning force. Every valve is strictly cleaned according to the process before leaving the factory to ensure worry free "cleanliness" throughout the entire process; The temperature of the cleaning tank is locked at 50-65 degrees. Within this temperature range, the activity of the cleaning solution is fully stimulated, and oil stains and impurities loosen and disintegrate from the valve surface. The drip time is finely controlled within 1000-2000 milliseconds, and the ultra long cleaning time reaches 100000-300000 seconds, effectively removing stubborn dirt such as oil, rust, carbon slag, etc.

　　本文由超聲波清洗機友情奉獻.更多有關的知識請點擊 http://m.zhuohengsh.com/ 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from an ultrasonic cleaning machine For more related knowledge, please click http://m.zhuohengsh.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.

上一篇：超聲波清洗機使用時聲音大是什么原因？
下一篇：超聲波清洗機：實驗室用超聲波清洗器，如何選購？